icon_h
icon_shiage

Coated CBN-Series for Hardened Steel Turning

BC8100series.png

bc8110_bc8120_main_gl.png

New Generation Coated CBN Grades

Wear and fracture resistance greatly improved for a wide range of continuous and interrupted applications.

Features of the Grade

New Advanced Ceramic Coating

BC8105

Offers excellent surface finishes.
Peeling resistance and adhesion strength are improved by having both lubricity and wear resistance.

BC8110

Chipping caused by built up edge is prevented with improved welding resistance. Improved wear and adhesion strength to the CBN surface.

BC8120

Chipping caused by built up edge is prevented with improved welding resistance. Improved adhesion to the coating to the CBN surface enhances peeling resistance.
The CBN is also improved in toughness by adopting new binder and sintering method.

BC8130

Peeling caused by severe impact and chipping are prevented with high fracture resistances. Improved adhesion strength to the CBN surface.

Optimised Substrate Technology

Obtimised subtrate techno.jpg

♦The new ultra micro-particle binder prevents linear crack development to avoid sudden fracturing.

SELECTION CRITERIA

C8100 Series Coated CBN Grades.jpg

BC8105 Highest Accuracy

BC8105_Highest_Accuracy.jpg

Application Range

Excellent surface finishes and close tolerances with long tool life For surface finishes up to Rz 2.4μm (Ra 0.6μm)

Surface Finish

  • Insert : NP-DNGA150608GS2
    Work Material : SMn433 (60HRC)
    Machining Methods :
    External Continuous Cutting
    Cutting Speed vc (m/min) : 176
    Feed f (mm/rev) : 0.09
    Depth of Cut ap (mm) : 0.15
    Cutting Mode : Wet (Emulsion)

  • BC8105 is first choice for superior surface finishes.

Graph.png

BC8110 High Speed Turning

BC8110_High_Speed_Turning.jpg

For Continuous Cutting

Covers a wide application range for continuous cutting

Tool Life (Flank Wear)

  • Insert : NP-CNGA120408GS2
    Work Material : SCr420 (60HRC)
    Machining Methods :
    External Continuous Cutting
    Cutting Speed vc (m/min) : 250
    Feed f (mm/rev) : 0.10
    Depth of Cut ap (mm) : 0.2
    Cutting Mode : Dry

  • BC8110 is first choice for high speed
  • finishing.


Graph2.png

BC8120 General Application

BC8120_General_Application.jpg

For Continuous and Light Interrupted Cutting

1st choice for roughing and pre-finishing
Covers a wide application range between continuous and light-interrupted machining

Test of Interrupted Cutting

Insert : NP-CNGA120408GA2
Work Material : SCr420 (60HRC)
Machining Methods :
External Interrupted Cutting
Cutting Speed vc (m/min) : 250
Feed f (mm/rev) : 0.15
Depth of Cut ap (mm) : 0.1
Cutting Mode : Dry

  • Cutting edge condition after 8000
  • impacts

  • BC8120conventional.jpg

Graph3.png

BC8130 Tough Machining

bc8100_15.png

For Unstable Applications and Heavy Interrupted Cutting

Tolerance accuracy maintained over a high number of impacts

Features of the Insert

Honing

honing.jpg

■ A variety of cutting edge preparations for all application.

Breaker

breaker.jpg

■ Breaker system for excellent chip control when finishing, removing carburized layers and hard-soft
machining.

Wiper Insert

Improving Surface Finish
Under the same machining conditions as conventional breakers, but with the feed rate increased, the surface finish of the workpiece can be improved.

Improving Efficiency
High feed rates not only shorten machining times but also make it possible to combine roughing and finishing operations.

Increased Tool Life
When using at high feed conditions, the time required to cut one component is decreased, thus more parts can be machined with each insert. In addition, the high feed rate prevents rubbing, therefore, delaying the progression of wear and increasing tool life.

Improving Chip Control
Under high feed conditions, the chips generated become thicker and are more easily broken, thus, chip control is improved.

Recommended Cutting Conditions and Performance

cutting condition.jpg

Cutting Performance

Insert : NP-CNGA120408
Work Material : Hardened Steel (HRC60)
Machining Methods : Continuous
Cutting Speed vc (m/min) : 120
Depth of Cut ap (mm) : 0.1
Cutting Mode : Dry

Graph5.png

Application Examples

application example.jpg

application example2.jpg

The above application examples are customer's application examples, so it can be different from the recommended conditions.

side_banner_contact_en-us.png
side_banner_youtube_en-gl.png
Page Top